Peugeot Forums banner

1 - 14 of 14 Posts

·
Registered
Joined
·
187 Posts
Discussion Starter #1
I need urgent help I changed my clutch and flywheel with one of the conversion ones from Peugeot dealer . and now the car wont start and says eco mode active and wont let me shut the windows and headlights don't work apart from sidelights. we took the battery out uncliped the maf and the crank sensor and moved the earth for the engine when dropping the gearbox . . any ideas how to fix this problem
 
G

·
Guest
Joined
·
0 Posts
Did you damage the crank sensor or its wiring during the clutch change?
The MAF won't stop the car starting..

As a thought, does the car give a 'beep beep' if you open the drivers door with the keys in the ignition?
 

·
Registered
Joined
·
187 Posts
Discussion Starter #3
Did you damage the crank sensor or its wiring during the clutch change?
The MAF won't stop the car starting..

As a thought, does the car give a 'beep beep' if you open the drivers door with the keys in the ignition?
how do you check the crank sensor on a 2.0 hdi and yes it does beep beep with the door open and key in the ignition but when i try to start it makes a bong noise
 
G

·
Guest
Joined
·
0 Posts
Eco mode will go when the car starts, a quick tow will sort that out.

As for the crank sensor, I don't know how to check it other than fit a known good one, but there are people here that could advise you better than me....
 

·
Registered
Joined
·
187 Posts
Discussion Starter #5
Eco mode will go when the car starts, a quick tow will sort that out.

As for the crank sensor, I don't know how to check it other than fit a known good one, but there are people here that could advise you better than me....
will eco mode stop the windows going up
 
G

·
Guest
Joined
·
0 Posts
Eco mode turns off lots of ancillaries to save the battery from going flat, maybe a jump start will give it a boost but be careful with the leads - keep the earths on the bodywork and the cars running together for a few minutes before disconnecting...

I'm no mechanic so maybe someone else can give more positive advise...:eek:
 

·
Registered
Joined
·
441 Posts
I need urgent help I changed my clutch and flywheel with one of the conversion ones from Peugeot dealer . and now the car wont start and says eco mode active and wont let me shut the windows and headlights don't work apart from sidelights. we took the battery out uncliped the maf and the crank sensor and moved the earth for the engine when dropping the gearbox . . any ideas how to fix this problem
If your sure everything is back the way it was undo the sensor plug and disconnect the battery wait 5 mins and reconnect sensor plug first then battery and try again.

failing this check the condition of crank sensor as mine split open and still worked just a bad starter?

if you had a failing DMF its poss that it has been smacked by spinning debris from flywheel? :thumb:
 

·
Registered
Joined
·
187 Posts
Discussion Starter #10
Would a magnet bolt tray damage the crank sensor if placed in it ?

Sent from my Hudl HT7S3 using Tapatalk
 

·
Moderator
Joined
·
6,276 Posts
its is possible as the sensor is magnetized so may have been affected.

Do you have access to planet or similar as live data will show rpm if sensor working.

You can also some times find that rev counter needle does not kick when you turn the key if sensor is shot.

Unless an electrical fault with the sensor it will not trigger engine light if faulty as ecu does not see cranking.

Lastly did you double check flywheel had same number of segments before fitting, and did you turn crankshaft backwards at any time as it can allow belt to slip and alter timing. Double check timing to be 100%
 

·
Registered
Joined
·
187 Posts
Discussion Starter #12
I went to Peugeot and got the conversion kit . they told me it was the right one and had all you need in it

Sent from my Hudl HT7S3 using Tapatalk
 
1 - 14 of 14 Posts
Top