Search Results for ‘diagbox’

Hello! I am bothering you with a question I have a 10 inch NAC screen, I want to see the possibility of removing the sensors from the screen and leave the camera as shown in the 7 inch screen. Is it possible from Diagbox to modify this?

Hello, I had in my 207(2006) some old and really bad multimedia and my radio information did not show on head central unit and that radio thing behind the steering wheel didn't work, so I replaced that multimedia with factory radio in hopes to solve my problems. It didnt solve any I only got...

I have a partner 2012 which has a hey DPF issue. I've taken the DPF off and cleaned it reinstalled it and using diagbox 7.02 I want to tell the car that it has a new DPF. Having checked out various posts on the forum my 7.02 version of diag box is not showing me a valid option for replacing...

Hi peeps,I'm looking for a bit of guidance. I HAVE 2011,3008 1.6HDI 112hp auto(semi) but wont go into gear, just goes back to 'N' with 'Gearbox Faulty' alert. Hooked up Diagbox 9.91,multiple faults(P0919,P1712,P1755,P1733,P1728,P1767,P0896) My question is,the part number coming up in Diagbox...

Afternoon all, New AGM battery went in about 3 years ago with a 4 year warranty. Over the past few months had the electrical fault warning appear and also it went flat after it was parked up for 5 days. Something isn't right! SInce i have warranty on it i have raised a call with the people i...

Hey guys, i bought a new head unit so i can have carplay, i mounted it and it works fine. The thing is that there is a beeping sound. I have to change the new headunits Vin to my cars Vin number. Therefore i bought a Diagbox 9.91. I have connected it and tried to change the vin but im keep...

Hi folks, I'm a little confused,I've just run/plugged my 'Diagbox' into my 3008 (2011) 1.6hdi because wont go into D/R/M (different story!) and I have just noticed that diagbox is saying the milage is around 40k more than whats on the speedo? Not sure if there is a genuine reason or should I be...

Good afternoon all. Have version 9.68 of the software with a lexia connector. Can somebody tell me the proper procedure for resetting the UREA 700 mile countdown. Waiting on a nox sensor replacement but need to use my car and would like to restart the counter to give me some extra leeway...

I used to use an old laptop and old version of PP2000 for my 2006 407sw ...and it worked really well. When I was looking to move on to a 508sw, I realised my PP2000 didn't support the 508, so I installed a newer version: DiagBox 7.02. Before I sold the 407 it developed yet another ABS sensor...

Afternoon all. I have a 60plate Peugeot 308 and am looking at fitting cruise control to it. I've ordered the stick and am confident in how to do it but realised too late that a general OBDII won't work for this. I was wondering if there was anyone in the southwest of England that has one...

Hi to all I have a actia vci on v4.3.2 firmware and i installed diagbox until v8.17 When i connect to my c4 grand picasso 2015 there is no calculators feedbacks. Vci is well recognised by diagbox, i heard the "click" into the vci when i start the diagnostic but i see " absence dialogue" at the...

Ive had to recently replace Injector nr 3 in my car, that went relatively smoothly considering it was my first repair job on a car. Then I tried to program the injector as the acceleration felt a tiny bit off to me. I went into DiagBox and changed the Injector code/serial to the new one and...

Hello all, So I recently ran a global test on my 308 using DiagBox 9.91 and I was hoping those with the knowledge might have time to have a little look through the results PDF attached and let me know if they see anything unusual. I'm still learning how to read and understand everything that...

Hello, I'd like full access to my 2016 Boxer, it's a Euro-5 2.2 early 2016 model (non-adblue). Before I spend lots of money on diag kit I'd like to know just how much functionality I'll have without it being connected to Peugeot servers? The people I'm thinking of buying the kit from either...

Good evening, There are 3 upgrades to my 2009 Expert tepee that I'd like to do. if all 3 are possible, i'd happily purchase the cable and install diagbox. If only one is possible, i'd travel to the nearest member with a working diagbox setup: 1. retrofit cruise control 2. activate daytime...

Hi I have just installed a cruise control stalk on my 307cc auto and I need someone as close to Burnley as possible, with the necessary interface, to activate it for me please, for a reasonable price. I will of course travel to your location if its not to far away.

So I decided to retrofit cruise control to my 57 plate 207 CC. I purchased a stalk and diagbox software off eBay. Fitted the stalk with no issues, had to cut a hole in the cowel cover but that was easy. Installed diagbox no issues and have followed a YouTube video on activating cruise in the...

Hi just recently I bought diagbox diagnostic tool from aliexpress with the version 9.68 Before I had the older version of the tool Wich worked only once! And then it stopped working. So after year I bought this one. I installed program as show in sellers video I did everything as shown in...

I have a pp2000/lexia 3 with a laptop that's running diagbox v8.55, and it worked well with my old Peugeot 206, but now that I have 407 SW it doesn't show 'global test' in PP2000. If I open Peugeot Planet, it only shows option 'test by ecu' and 'under it' 'Built in systems interface' and...

Hey, guys. I'm new to this forum so let me introduce myself first. I'm a proud second and who knows (third, fourth etc.) owner of Peugeot 206 SW. It was my dream car and finally got one and I had it for year and half. So recently I've been trying to make some "mods" on it and by "mods" - I mean...