Peugeot 407 hdi 2.0 wonít start after doing cam belt - Peugeot Forums
Peugeot Forums - Peueot - Citroen Community
Home :: Peugeot Forums :: Rules :: Articles :: About Us :: Partner Vendors :: Advertise


Go Back   Peugeot Forums > Peugeot Models > 407
PeugeotForums.com is the premier Peugeot All Forum on the internet. Registered Users do not see the above ads.
Like Tree1Likes
  • 1 Post By reliable406

Reply
 
LinkBack Thread Tools Display Modes
Old 01-07-18, 08:08 AM   #1
Junior Member
 
Join Date: Jul 2018
Posts: 5
Exclamation Peugeot 407 hdi 2.0 wonít start after doing cam belt

Just after anybodyís 2 cents worth I have changed my cam belt on my 2009 407 hdi upon trying to restart it doesnít go and checket pp2000 and diagbox and getting fault codes po341 and po017
Which is cam angle sensor signal failure and starting monitoring timed out
Have tried new cam sensor off a known running engine still no go itís crankng at 300 rpm and has 400 bar fuel pressure
Now at a loss 🤔
Thanks for any input
Thanks again I am new here
Nathanlatta is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-07-18, 08:23 AM   #2
Senior Member
 
Join Date: Oct 2012
Location: falkirk
Posts: 14,018
Default

Put planet back on and diagnose PROPERLY read LIVE DATA to check fuel pressure cranking speed and cam and crank sync

You will no doubt find you have no cam sync because your timing is not correct OR you have forgotten to put timing disc back on crank pulley these are the 2 common mistakes
__________________
assume nothing check everything twice !!
reliable406 is offline   Reply With Quote Quick reply to this message
Old 01-07-18, 11:29 AM   #3
Junior Member
 
Join Date: Jul 2018
Posts: 5
Default hdi no start

thanks for the reply have looked at live data and crank speed was from memory 280 rpm fuel pressure was 380bar we had no cam crank sink but I presume that was because of fault po341 which diagbox says cam sensor no signal. I presume crank sensor is ok as we can see rpm cranking on live data I have also tried another cam sensor from another engine that was running when we reconnected the battery it did spark hope this didn't cause a problem
thanks for your reply
Nathanlatta is offline   Reply With Quote Quick reply to this message
 
Old 01-07-18, 01:02 PM   #4
Senior Member
 
Join Date: Oct 2012
Location: falkirk
Posts: 14,018
Default

If you have no cam sync it wont start simple as that but that DOES NOT mean the sensor is faulty people read fault codes and assume wrongly that the code means the part is faulty.

Recheck timing make sure the pins still go in if thats ok then you may well have damaged something relating to the cam sensor wiring somewhere
__________________
assume nothing check everything twice !!
reliable406 is offline   Reply With Quote Quick reply to this message
Old 01-07-18, 10:29 PM   #5
Junior Member
 
Join Date: Jul 2018
Posts: 5
Default

thanks for the reply thats a bit confusing for a novice you would think a code that says no cam sensor signal was getting no signal will have a look tonight after work and recheck timing pins then if that doesn't work check continuity of sensor wires back to the ecu
thanks Craig
Nathanlatta is offline   Reply With Quote Quick reply to this message
Old 02-07-18, 01:52 PM   #6
Junior Member
 
Join Date: Jul 2018
Posts: 5
Default

thanks for you help checked the cam timing and we where a t ooth out
Nathanlatta is offline   Reply With Quote Quick reply to this message
Old 02-07-18, 02:16 PM   #7
Senior Member
 
Join Date: Oct 2012
Location: falkirk
Posts: 14,018
Default

Just like i say in my sig check everything twice

Timing being a tooth out gives no sync which in some cases would give you a cam sensor fault code.

As you have now learned fault code does not mean faulty part !
mooi1uk likes this.
__________________
assume nothing check everything twice !!
reliable406 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Peugeot Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 11:02 PM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.