Peugeot 407 2.0 HDI Problem - Peugeot Forums
Peugeot Forums - Peueot - Citroen Community
Home :: Peugeot Forums :: Rules :: Articles :: About Us :: Partner Vendors :: Advertise


Go Back   Peugeot Forums > Peugeot Models > 407
PeugeotForums.com is the premier Peugeot All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 27-05-18, 03:25 PM   #1
Junior Member
 
Join Date: May 2018
Posts: 2
Default Peugeot 407 2.0 HDI Problem

Hi to all,

I have scanned the car with Lexia PP2000, and there are 2 fault codes:

1. Cooling Circuit By-Pass Electrovalve
2. Pre/post heating relay circuit

ecu.jpg

The car sometimes juddering randomly, also the EGR valve is blanked by the previous owner.

What my be the problem.

Thanks in advance.
reasson is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 27-05-18, 08:03 PM   #2
rwb
Senior Member
 
rwb's Avatar
 
Join Date: Jun 2012
Location: Telford
Posts: 1,000
Send a message via Skype™ to rwb
Default

Hi & welcome.

Everyone has the glow plug fault, so that's probably a red herring. (Although I did actually get rid of mine by putting in new glow plugs; go figure.)

"cooling bypass circuit" means the intercooler bypass. A pair of butterflies (called the air doser) in the air intake can switch air through a path that bypasses the intercooler. This is done during particle filter regeneration.

Each butterfly reports its actual position back to the ECU, and if the value received doesn't match the value the ECU requested then this is the sort of fault you see.

Things to try:
* actuators test
* check requested vs actual position in parameter measurements.
__________________
407 2.2 HDi & CitroŽn C6
I'm on the
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
.
rwb is offline   Reply With Quote Quick reply to this message
Old 05-06-18, 11:38 PM   #3
Junior Member
 
Join Date: Jun 2018
Posts: 3
Default

Quote:
Originally Posted by reasson View Post
Hi to all,

I have scanned the car with Lexia PP2000, and there are 2 fault codes:

1. Cooling Circuit By-Pass Electrovalve
2. Pre/post heating relay circuit

Attachment 78538

The car sometimes juddering randomly, also the EGR valve is blanked by the previous owner.

What my be the problem.

Thanks in advance.
You didnt mention the engine and year.

Some early models were never fitted with the electrovalve (for controlling teh coolant flow) and have a regular thermostat. if you check your thermostat housing check if you have an electrovalve. If not, you can ignore the fault, if your coolant temperatures are normal. But it would not cause you juddering.

About the heating relay, the relay is below the Engine ECU, in the boot. If the relay is bad, it is cheap and easy to replace. It could also be glow plugs. But these cars dont use glow plugs unless its -5 degrees.

So your issue is elsewhere. Check vericle parameters when running and paste screenshot here.

Thank god your EGR is blanked, it is only good for your engine.
aneesh84 is offline   Reply With Quote Quick reply to this message
 
Old 19-06-18, 12:36 PM   #4
Junior Member
 
Join Date: May 2018
Posts: 2
Default

Quote:
Originally Posted by aneesh84 View Post
You didnt mention the engine and year.

Some early models were never fitted with the electrovalve (for controlling teh coolant flow) and have a regular thermostat. if you check your thermostat housing check if you have an electrovalve. If not, you can ignore the fault, if your coolant temperatures are normal. But it would not cause you juddering.

About the heating relay, the relay is below the Engine ECU, in the boot. If the relay is bad, it is cheap and easy to replace. It could also be glow plugs. But these cars dont use glow plugs unless its -5 degrees.

So your issue is elsewhere. Check vericle parameters when running and paste screenshot here.

Thank god your EGR is blanked, it is only good for your engine.
Thanks for the replay,

My car is from 2004 2.0 HDI 16v Siemens, strange thing is that i removed the engine plastic cover because have broken mountings and suddenly the juddering stopped and i don't have this problem anymore. So assume there is some electrical problem as the plastic cover does not fit in the mounting holes and touch some of the wiring in the engine. One more question where exactly to look for the thermostat electrovalve, if it present to check if the PP2000 error can be eliminated.

Thanks.
reasson is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Peugeot Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 09:54 PM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.