Misfire please help! - Peugeot Forums
Peugeot Forums - Peueot - Citroen Community
Home :: Peugeot Forums :: Rules :: Articles :: About Us :: Partner Vendors :: Advertise


Go Back   Peugeot Forums > Peugeot Models > 207
PeugeotForums.com is the premier Peugeot All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 24-01-18, 11:36 PM   #1
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default Misfire please help!

So been having a problem with my 207 1.6 thp 150 on a 2008 for last 6 month now with misfiring. First time it happened it said cylinder 1 and 3 misfiring so changed all 4 coils which sorted it for a couple of month then it come back with same codes so changed the sparks as coils looked fine and was only 2 month old. Itís now happened again with codes for cylinder 2 and 4 misfire. I had the walnut blast done on intake valves on Saturday as I thought maybe that was the problem but obviously not! So Iím kind of stuck what to try now as i canít just keep replacing plugs and coils as their not cheap so any suggestions would be appreciated. I have read maybe some kind of back pressure from catalytic converters if blocked/faulty may cause this? I have attached picture of vault codes that were taken tonight. Anti pollution fault come up on way to work and was still on at my break 4 hours later but on way home which was another 4 hours after the light went off but codes were still stored as i code read it when I got home.
Attached Thumbnails
46c1aa58-c837-4b6e-b254-fab43684508c_1516836969323.jpg  
Nick91uk is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 24-01-18, 11:38 PM   #2
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default

If you canít see picture the codes were
P1336 combustion misfire on on unspecified cylinders
P1340 combustion misfire on cylinder 4
P1338 combustion misfire on cylinder 2
Nick91uk is offline   Reply With Quote Quick reply to this message
Old 25-01-18, 06:33 PM   #3
Senior Member
 
Join Date: Sep 2016
Location: New Zealand
Posts: 1,134
Default

Misfire need not be a faulty coil or spark plug, it could be the injector, bad wiring/connections to any of the above, a failing sensor, sticky valves... the codes thrown are only the end result. The actual cause may be further up the food chain.

You need to get live readings, start with looking at the injectors. Also do a careful examination of the wiring and all plugs/pin contacts on coils/injectors/ecu/bsi/various sensors.
WillNZ is offline   Reply With Quote Quick reply to this message
 
Old 25-01-18, 06:58 PM   #4
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default

Ok thanks for that Iíve done the live data and all injectors working as should
Nick91uk is offline   Reply With Quote Quick reply to this message
Old 25-01-18, 07:49 PM   #5
Moderator
 
windy1603's Avatar
 
Join Date: Sep 2012
Location: Hertfordshire
Posts: 5,566
Default

check fuel pressure readings THP engine can suffer misfires if HP pump is failing (quite common).
__________________
DS5 & DS4 DSport 2.0 HDI 2012, 107 1.0 Urban 2006, 208 1.6 e-HDI Feline 2014, Suzuki RGV 250M 1989 (Money Pit)
windy1603 is offline   Reply With Quote Quick reply to this message
Old 25-01-18, 08:59 PM   #6
Senior Member
 
Join Date: Nov 2017
Posts: 131
Default

Where the coils off Euro car parts ?
mechcanico is offline   Reply With Quote Quick reply to this message
Old 26-01-18, 12:07 AM   #7
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default

Yes been told about high pressure fuel pump and their rather expensive and yes from euro car parts got the proper Bosch ones though
Nick91uk is offline   Reply With Quote Quick reply to this message
Old 26-01-18, 12:08 AM   #8
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default

Any idea on what the fuel pressure readings should be I have got a snap on diagnostic machine that can do live data etc
Nick91uk is offline   Reply With Quote Quick reply to this message
Old 26-01-18, 01:56 PM   #9
Senior Member
 
Join Date: Nov 2017
Posts: 131
Default

We have seen all kinds of trouble with anything off ECP thatís made by Bosch ....batteryís , air mass meters , egrs ,coil packs , pencil coils everything.

Iím not sayings thatís your issue but you say after fitting new ones it behaves for a few months .....coincidence?? Maybe .....

Just bare it in mind , if you get another set of coils try Beru ones instead .
mechcanico is offline   Reply With Quote Quick reply to this message
Old 26-01-18, 02:07 PM   #10
Junior Member
 
Join Date: May 2017
Location: South Yorkshire
Posts: 20
Default

Ok thanks for that worth a thought. Just done the live data check and I have a weak downstream sensor status which is the one after the cat so maybe thatís not helping either haha
Nick91uk is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Peugeot Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 01:01 PM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.