Heater control bulbs - Peugeot Forums
Peugeot Forums - Peueot - Citroen Community
Home :: Peugeot Forums :: Rules :: Articles :: About Us :: Partner Vendors :: Advertise


Go Back   Peugeot Forums > Peugeot Models > 207
PeugeotForums.com is the premier Peugeot All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 31-10-18, 04:21 PM   #1
Junior Member
 
Join Date: Oct 2018
Posts: 3
Default Heater control bulbs

One of my heater control bulbs needs replacing and I cannot get the unit out the centre console at all . I've removed the side trim. Removed the 4 screws and pulled out the lock buttons at the bottom aswell as removing the single din shelf above the heaters.

The heater into only moves inwards, no way to pull it out as the two clips prevent it going outwards.

Any help please.

What a stupid design just to replace a bulb 😤
Baxter4130 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-12-18, 08:46 PM   #2
Junior Member
 
Join Date: Nov 2018
Posts: 18
Default

I've just written a whole long winded story about this repair.

You're right, there is literally no give in the module, its almost impossible to manipulate it round in the dash cavity. Its a ridiculous design.

Here's the post I just wrote...
https://www.peugeotforums.com/forums...l-bulb-257369/
whitebake is offline   Reply With Quote Quick reply to this message
Old 07-12-18, 04:45 PM   #3
Junior Member
 
Join Date: Feb 2015
Location: Lutterworth, Leicestershire
Posts: 4
Angry

I recently had a similar problem after the rotary temperature control jammed. Like you, I battled for hours (?!) without success, and finally decided to remove the whole heater control unit. After removing the trim and fixing screws, I removed the switch panel beneath the heater control unit, and then the storage shelf above it. Then I disconnected the radio and took that out too! This gave me a bit more room to unclip the three control cables and unplug the two multi-connectors. This allowed enough room to push everything out of the way to twist and lower the unit out. It was still a bit of a fiddle to get the bulb holders out, and finally I found the rotary control was jammed by a spent bulb rattling around inside - obviously dropped in when it was being replaced. Aaaargh!
Replacing the unit wasn't too bad - fortunately the cables have different colours and connectors so you can't get them mixed up, although they require a bit of brute force with a screwdriver to get them closed!

Note! As I was expecting to need a complete replacement unit, I had bought one off Ebay for a few pounds . . . . it still had the ends of the control cables and the wires attached so I could practice clipping and unclipping them! Also photos of the units for sale are very helpful too!
I hope all of this will make it a bit easier for others. Good luck.
JohnM is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Peugeot Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 08:34 AM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.