Help with bended front - Peugeot Forums
Peugeot Forums - Peueot - Citroen Community
Home :: Peugeot Forums :: Rules :: Articles :: About Us :: Partner Vendors :: Advertise


Go Back   Peugeot Forums > Peugeot Models > 107
PeugeotForums.com is the premier Peugeot All Forum on the internet. Registered Users do not see the above ads.
Like Tree2Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 11-06-14, 04:49 PM   #1
Inactive User
 
Join Date: Jun 2014
Posts: 11
Default Help with bended front

Hello!

I need to adjust the front of my Peugeot.
Can someone with 107 measure the distances with red arrow in the pic and post here? Thanks a lot.

2013-09-06_motorul_01_dist.jpg

I have a Peugeot 107, 5 doors, from 2008.
remsan is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 11-06-14, 06:15 PM   #2
Inactive User
 
Join Date: Mar 2014
Location: Just outside Belfast
Posts: 177
Default

You will need more specific datum points on the bulkhead if you want accuracy. Also do you want the measure to the bolt centres at the front?
andy308sw is offline   Reply With Quote Quick reply to this message
Old 11-06-14, 06:25 PM   #3
Inactive User
 
Join Date: Jun 2014
Posts: 11
Default

Yes! I want to measure from the center of those bolts to the rubber. The shortest distance. I've tested on a Toyota Aygo but they are diferent, as I expected .


Quote:
Originally Posted by andy308sw View Post
You will need more specific datum points on the bulkhead if you want accuracy. Also do you want the measure to the bolt centres at the front?
remsan is offline   Reply With Quote Quick reply to this message
 
Old 11-06-14, 06:35 PM   #4
Inactive User
 
Join Date: Mar 2014
Location: Just outside Belfast
Posts: 177
Default

Placing the tip of my tape measure at the rubber and measuring to the centre of each bolt, I get 32.5 cm. Please note, this is the same for each.

Have you had an accident? Is the front misaligned? Take care if you are going to pull this out, you could really run in to problems with bonnet and wing alignment. Any pictures?
andy308sw is offline   Reply With Quote Quick reply to this message
Old 11-06-14, 07:31 PM   #5
Inactive User
 
Join Date: Jun 2014
Posts: 11
Default

Thanks! Yes, the car had an accident. I will post a movie when I am completly done with it . Tomorow I will get the hood as well.


2014-06-06_peugeot_montare_fb.jpg

Quote:
Originally Posted by andy308sw View Post
Placing the tip of my tape measure at the rubber and measuring to the centre of each bolt, I get 32.5 cm. Please note, this is the same for each.

Have you had an accident? Is the front misaligned? Take care if you are going to pull this out, you could really run in to problems with bonnet and wing alignment. Any pictures?
remsan is offline   Reply With Quote Quick reply to this message
Old 11-06-14, 07:34 PM   #6
Inactive User
 
Join Date: Mar 2014
Location: Just outside Belfast
Posts: 177
Default

Wow! Some work there. Hope the measurements help. Good luck
andy308sw is offline   Reply With Quote Quick reply to this message
Old 12-06-14, 01:15 PM   #7
chopper1192
Guest
 
Posts: n/a
Default

There is no way that will have neatly and conveniently bent in 2 dimensions only.
  Reply With Quote Quick reply to this message
Old 12-06-14, 06:10 PM   #8
Inactive User
 
Join Date: Jun 2014
Posts: 11
Default

Quote:
Originally Posted by chopper1192 View Post
There is no way that will have neatly and conveniently bent in 2 dimensions only.
Fully agree. But my first attempt is to get it running.
Today I got the hood. It almost fits. I only need to move the front to left, about 5mm.
I will not be able to work with it for the next week so I will have to wait a little.
remsan is offline   Reply With Quote Quick reply to this message
Old 28-06-14, 09:18 PM   #9
Inactive User
 
Join Date: Mar 2014
Location: Just outside Belfast
Posts: 177
Default

Any progress Remsan?
andy308sw is offline   Reply With Quote Quick reply to this message
Old 28-06-14, 10:51 PM   #10
Inactive User
 
Join Date: Jun 2014
Posts: 11
Default

Yes, was still a couple of mm left but the bonnet is going down now.
So today I drove it without any problem.
I put the hole movie on youtube

Thanks for the help!

https://www.youtube.com/watch?v=Hp3a0b4Vt-c

Quote:
Originally Posted by andy308sw View Post
Any progress Remsan?
andy308sw likes this.
remsan is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Peugeot Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT. The time now is 10:17 PM.



Powered by vBulletin® Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.