806 started then clonked and stalled

purpletrance · 05-01-2011, 02:52 PM

Started my 2000-X 2.0l 806 yesterday. Seconds later, it made a dull clonking sound and stalled. It would then not start. Starter motor operates, but engine doesn't turn over. Car was in neutral and hadn't been put into gear. 95k miles on the clock. Cambelt replaced at 80k. Any pointers would be appreciated. Thanks.

davidireland · 05-01-2011, 05:17 PM

When the starter is operating, is the crankshaft turning?
Can you see the camshaft turning?

purpletrance · 05-01-2011, 07:55 PM

David. It's dark now, but in the morning I'll check by looking through the oil filler aperture and get back to you. Thanks, Mark.

purpletrance · 05-02-2011, 12:21 PM

Hi David. The camshaft is definitely turning when the starter motor is operating. Mark.

davidireland · 05-02-2011, 08:30 PM

ok. Doesn't mean the timing is not out though. You need to get the car onto Peugeot Planet. Check to see if theres cam crank synchronisation.
Go from there.

purpletrance · 05-02-2011, 08:40 PM

Ok David. Will do. Thanks for your advice.

05-01-2011, 02:52 PM	#1
purpletrance Junior Member Join Date: May 2011 Posts: 5	806 started then clonked and stalled Started my 2000-X 2.0l 806 yesterday. Seconds later, it made a dull clonking sound and stalled. It would then not start. Starter motor operates, but engine doesn't turn over. Car was in neutral and hadn't been put into gear. 95k miles on the clock. Cambelt replaced at 80k. Any pointers would be appreciated. Thanks. Share Share this post on Digg Del.icio.us Technorati Twitter

05-01-2011, 05:17 PM	#2
davidireland Senior Member Join Date: Jan 2010 Location: Southern Ireland Posts: 2,332	When the starter is operating, is the crankshaft turning? Can you see the camshaft turning? Share Share this post on Digg Del.icio.us Technorati Twitter __________________ Peugeot Master Tech/Citroen Tech

05-01-2011, 07:55 PM	#3
purpletrance Junior Member Join Date: May 2011 Posts: 5	David. It's dark now, but in the morning I'll check by looking through the oil filler aperture and get back to you. Thanks, Mark. Share Share this post on Digg Del.icio.us Technorati Twitter

05-02-2011, 12:21 PM	#4
purpletrance Junior Member Join Date: May 2011 Posts: 5	Hi David. The camshaft is definitely turning when the starter motor is operating. Mark. Share Share this post on Digg Del.icio.us Technorati Twitter

05-02-2011, 08:30 PM	#5
davidireland Senior Member Join Date: Jan 2010 Location: Southern Ireland Posts: 2,332	ok. Doesn't mean the timing is not out though. You need to get the car onto Peugeot Planet. Check to see if theres cam crank synchronisation. Go from there. Share Share this post on Digg Del.icio.us Technorati Twitter __________________ Peugeot Master Tech/Citroen Tech

05-02-2011, 08:40 PM	#6
purpletrance Junior Member Join Date: May 2011 Posts: 5	Ok David. Will do. Thanks for your advice. Share Share this post on Digg Del.icio.us Technorati Twitter

Remove Advertisements Sponsored Links
PeugeotForums.com Advertisement

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode