![]() |
| |
|
|||||||
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
#1 |
|
Member
Join Date: Jan 2012
Location: west lothian
Posts: 31
|
Hi, i think my outside temperature sensor doesnt work as im getting no reading on my display,so if anyone can tell me where it is and how to remove/replace it,it would be appreciated.just recently bought the car and it seems fine except for one or two little niggles etc bootlid "o" button and telephone sim card,other than that all seems ok at the moment. so any help will be welcome....thanks in advance
|
|
|
|
| Sponsored Links | |||
Advertisement | |||
|
|
#2 |
|
Senior Member
Join Date: Sep 2010
Location: St Austell, Cornwall
Posts: 2,969
|
The sensor is in the driver's door mirror - a little black plastic dome sticking out the bottom of the mirror casing
__________________
407SW 2.0HDI 136 SE 2005 ex. 306 2.0HDI 90 (x2) |
|
|
|
|
|
#3 |
|
Senior Member
Join Date: Sep 2011
Location: Atherton, Boston Lincs, or Akbuk, Turkey
Posts: 932
|
Boot o button easy fix. my one just needed re bending and is fine now. look it up in search box its well documented.
PS Nice tip jm I always wondered where it lived. Last edited by sterion75; 01-30-2012 at 07:37 PM. Reason: ps |
|
|
|
|
|
#4 |
|
Senior Member
Join Date: Sep 2011
Location: Atherton, Boston Lincs, or Akbuk, Turkey
Posts: 932
|
The boot button problem will be broken wires as they enter or leave the rubber gaitor from the boot, or the button itself needing some diy adjustment. Good luck auldyin
|
|
|
|
|
|
#5 |
|
Member
Join Date: Jan 2012
Location: west lothian
Posts: 31
|
thanks for the replys guys,jm i take it i can remove the rear of the mirror cover and gain access to the sensor from there,i assume because there is no reading on my display that the sensor is at fault or is there possibly another cause or is it a common fault.....sterion bent the back of the button about a little bit and now it works perfect...
|
|
|
|
|
|
#6 |
|
Senior Member
Join Date: Sep 2011
Location: Atherton, Boston Lincs, or Akbuk, Turkey
Posts: 932
|
auldyin, get some boot card plastic fixing clips because you will break several removing it to get to the switch.
Wow nearly forgot is boot locking enabled, i believe its in the mfd ecu entered directly, not with planet. Last edited by sterion75; 01-30-2012 at 09:21 PM. |
|
|
|
|
|
#7 |
|
Member
Join Date: Jan 2012
Location: west lothian
Posts: 31
|
Cheers sterion,i did break a couple of clips but just bent the switch and twisted it a little and now it works perfect,so just need to buy a couple of new clips then try the temp sensor hopefully i dont break anything on the wing mirror.
|
|
|
|
|
|
#8 |
|
Senior Member
Join Date: Feb 2011
Location: PLYMOUTH,DEVON
Posts: 535
|
hi temperature showing like that -- or nothing?
__________________
407 1.6 HDI FAP 110 PP OWNER PLYMOUTH
|
|
|
|
|
|
#9 |
|
Member
Join Date: Jan 2012
Location: west lothian
Posts: 31
|
Magma, im getting no reading on the display it just show _ _c or something like that... thanks
|
|
|
|
|
|
#10 |
|
Senior Member
Join Date: Jan 2010
Location: south shields,tyneside
Posts: 1,631
|
this might help
__________________
![]() 2004 136bhp 2.0 hdi |
|
|
|
| Sponsored Links | |
Advertisement | |
![]() |
| Thread Tools | |
| Display Modes | |
|
|